钣金行业内常用的冷轧板、镀锌板、电解板折弯表分享

Hyatt.Chan

特别注意这个表是我们公司自己用的，链接了材料SPCC/SGCC/SECC三种材料
!# Creo/TABLE
!#
! [] S 92;
! [] W  8;
![A] W 10;
![B] W 10;
"!"
"!     90度折弯 - 需要原料的直线长度(L)"
"!"
"! 对于表范围以外的R和T，使用下列值，"
"!"
"FORMULA"
"IF(R)<4"
"L=A"
"ELSE"
"L = (0.785398 * T) + (PI * R) / 2.0"
"ENDIF"
"END FORMULA"
"!"
"! 该表可用于以下材料"
"START MATERIALS"
"SPCC"
"SECC"
"END MATERIALS"
"!"
"TABLE"
"!                            内侧  半径(R)"
" " 0.000000 0.100000 0.200000 0.300000 0.400000 0.500000 0.600000 0.700000 0.800000 0.900000 1.000000 1.100000 1.200000 1.300000 1.400000 1.500000 1.600000 1.700000 1.800000 1.900000 2.000000 2.500000 3.000000 3.500000
"!厚度  (T)"
0.500000 0.200000 0.400000 0.600000 0.800000 1.000000 1.200000 1.400000 1.600000 1.800000 2.000000 2.200000 2.400000 2.600000 2.800000 3.000000 3.200000 3.400000 3.600000 3.800000 4.000000 4.200000 5.200000 6.200000 7.200000
0.800000 0.300000 0.500000 0.700000 0.900000 1.100000 1.300000 1.500000 1.700000 1.900000 2.100000 2.300000 2.500000 2.700000 2.900000 3.100000 3.300000 3.500000 3.700000 3.900000 4.100000 4.300000 5.300000 6.300000 7.300000
1.000000 0.300000 0.500000 0.700000 0.900000 1.100000 1.300000 1.500000 1.700000 1.900000 2.100000 2.300000 2.500000 2.700000 2.900000 3.100000 3.300000 3.500000 3.700000 3.900000 4.100000 4.300000 5.300000 6.300000 7.300000
1.200000 0.300000 0.500000 0.700000 0.900000 1.100000 1.300000 1.500000 1.700000 1.900000 2.100000 2.300000 2.500000 2.700000 2.900000 3.100000 3.300000 3.500000 3.700000 3.900000 4.100000 4.300000 5.300000 6.300000 7.300000
1.500000 0.500000 0.700000 0.900000 1.100000 1.300000 1.500000 1.700000 1.900000 2.100000 2.300000 2.500000 2.700000 2.900000 3.100000 3.300000 3.500000 3.700000 3.900000 4.100000 4.300000 4.500000 5.500000 6.500000 7.500000
2.000000 0.600000 0.800000 1.000000 1.200000 1.400000 1.600000 1.800000 2.000000 2.200000 2.400000 2.600000 2.800000 3.000000 3.200000 3.400000 3.600000 3.800000 4.000000 4.200000 4.400000 4.600000 5.600000 6.600000 7.600000
2.500000 0.700000 0.900000 1.100000 1.300000 1.500000 1.700000 1.900000 2.100000 2.300000 2.500000 2.700000 2.900000 3.100000 3.300000 3.500000 3.700000 3.900000 4.100000 4.300000 4.500000 4.700000 5.700000 6.700000 7.700000
3.000000 0.900000 1.100000 1.300000 1.500000 1.700000 1.900000 2.100000 2.300000 2.500000 2.700000 2.900000 3.100000 3.300000 3.500000 3.700000 3.900000 4.100000 4.300000 4.500000 4.700000 4.900000 5.900000 6.900000 7.900000

qq202777898

感谢分享

abc13456533895

bed文件能分享，感谢感谢

aeola

感谢分享

Hyatt.Chan

abc13456533895 发表于 2024-7-31 16:33
bed文件能分享，感谢感谢

可以的

Hyatt.Chan

abc13456533895 发表于 2024-7-31 16:33
bed文件能分享，感谢感谢

[url=钣金设计折弯参数bend文件分享 http://www.proewildfire.cn/thread-180431-1-1.html (出处: 野火论坛)]钣金设计折弯参数bend文件分享 [/url]

308816291

只限于90度折弯吗？小于或大于90度，是否可以适用

Hyatt.Chan

308816291 发表于 2024-8-2 20:52
只限于90度折弯吗？小于或大于90度，是否可以适用

不可以，要手动调整哦

317720499

电解板不就是镀锌板吗

fuf4321@163.com

感谢分享